5 in 1 Hydraulic Iron Worker Machine
STANDARD EQUIPMENT
- Variable Stroke Adjustment With Limit Switch
- Quick Change Die Holder 3 in 1 – 50, 73 & Angle Punching
- Hydraulic Hold-Down
- Back Gauge
- Die Light
- Operating Mode (Inching/Auto)
- Emergency Stop Switch
- Movable Foot Switch
- Table for Punch Station
- Operation & Maintenance Manual Book
OPTIONAL EQUIPMENT
- Extra Throat Depth
- NC Gauge
Standard blade sets along with the ironworker Machine
- Punch and Die – 10 Set (Diameter between 8 mm to 20 mm)
- Angle Cutting Blade Punching
- Flate Bar Shearing Blade
Any one set of die:
- Â Round Bar & Squre Bar
- Â I Section Die
- Â C Section Die
- Â Customized Die
- Â
Any one set of Notching Die:
- Â V-Notching Die
- Square Notching Die
Hydraulic Ironworker Pieces
FRAME CONSTRUCTION
Ironworker Machine Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the ironworker machine is never disturbed.
TABLE & SLIDE (Ram)
Table are made of high grade heavy duty cast iron and properly seasoned. Slide are fabricated from IS-2062 graded rollated steel plates is deeply reinforced and fines ironworker machines after stress reliving. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.
CYLINDER
The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
HYDRAULIC SYSTEM
The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise system is placed on the rear side of ironworker machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and ironworker machine from overload. This system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
ELECTRICAL CONTROL PANEL
The electrical control panel is located on the left hand side of the hydraulic ironworker machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Technical Parameters
| Model No. | RIW 50 | RIW 60 | RIW 75 | RIW 90 | RIW 120 | RIW 150 | ||
|---|---|---|---|---|---|---|---|---|
| PUNCHING | ||||||||
| Punching Pressure | 50 Ton | 60 Ton | 75 Ton | 90 Ton | 120 Ton | 150 Ton | ||
| Punch Capacity (Diameter x Thickness) Material Strength Of 450 N/MM' | ø 20 x 15 | ø 22 x16 | ø 22 x 20 | ø 26 x 22 | ø 26 x 26 | ø 33 x 27 | ||
| ø 35 x 8 | ø 45 x 8 | ø 50 x 9 | ø 50 x 12 | ø 50 x 15 | ø 50 x 18 | |||
| Throat Depth | 175 | 275 | 310 | 310 | 310 | 350 | ||
| Maximum Stock Length | 60 | 100 | 100 | 100 | 100 | 100 | ||
| Cycles I Min. (20mm Stroke) | 30 | 25 / 32 | 20 | 21 | 21 | 20 | ||
| Working Height Up to Die | 910 | 910 | 950 | 950 | 1020 | |||
| FLAT SHEARING | ||||||||
| Flat Bar Shear | 250 x 8 | 300 x 12 | 350 x 15 | 460 x 15 | 610 x 16 | 610 x 18 | ||
| (Width x Thickness) | 180 x 12 | 240 x 16 | 240 x 20 | 300 x 20 | 400 x 20 | 400 x 25 | ||
| Blade Length | 260 | 310 | 360 | 465 | 620 | 620 | ||
| Angle Flange Trim | 65 | 65 | 75 | 100 | 100 | 100 | ||
| Working Height | 800 | 820 | 920 | 920 | 950 | 950 | ||
| ANGLE SHEARING | ||||||||
| At 90 Shearing | 80 x 80 x 8 | 100 x 100 x 10 | 130 x 130 x 13 | 152 x 152 x 13 | 152 x 152 x 15 | 152 x 152 x 18 | ||
| At 45 Miter Shearing | 50 x 50 x 6 | 50 x 50 x 6 | 65 x 65 x 8 | 80 x 80 x 10 | 80 x 80 x 10 | 80 x 80 x 10 | ||
| Working Height | 1080 | 1080 | 1150 | 1150 | 1150 | 1160 | ||
| BAR SHEARING | ||||||||
| Round Bar Shear (Dia.) | 25 | 32 | 40 | 50 | 50 | 50 | ||
| Square Bar Shear | 25 x 25 | 32 x 32 | 38 x 38 | 50 x 50 | 50 x 50 | 50 x 50 | ||
| Channel Shear | - | 100* | 130* | 152* | 152* | 180* | ||
| I Beam Shear | - | 100* | 130* | 152* | 152* | 180* | ||
| Working Height | 1150 | 1150 | 1300 | 1300 | 1315 | 1315 | ||
| NOTCHING | ||||||||
| Rectangular (W x D x T) | 30 x 60 x 5 | 50.8 x 90 x 6 | 50.8 x 90 x 9 | 50.8 x 90 x 12 | 63.5 x 90 x 12 | 63.5 x 90 x 13 | ||
| Vee-Natcher (Side x Side x T) | 60 x 32 x 6* | 80 x 50 x 9* | 90 x 90 x 8* | 90 x 90 x 10* | 105 x 105 x 12* | 105 x 105 x 13* | ||
| Large Vee-Natcher (Side x Side x T) | - | - | 145 x 145 x 8 | 145 x 145 x 10 | 145 x 145 x 12 | 145 x 145 x 13 | ||
| Working Height | 850 | 850 | 850 | 860 | 860 | 860 | ||
| SPECIAL TOOLING | ||||||||
| Single Vee Press Brake (W x T) | 160 x 6 | 250 x 10 | 250 x 15 | 250 x 15 | 250 x 20 | 250 x 20 | ||
| Multi Vee Press Brake (W x T) | - | 400 x 8 | 500 x 5 | 500 x 5 | 700 x 5 | 700 x 5 | ||
| Angle Bending | 65 x 6 | 76 x 8 | 102 x 6 | 102 x 8 | 102 x 13 | 102 x 13 | ||
| Pipe Notching (Dia.) | 114 | 114 | 114 | 114 | 114 | 114 | ||
| OTHER | ||||||||
| Electric Power (HP) | 5 HP | 5 HP | 7.5 HP | 10 HP | 10 HP | 15 HP | ||
| Net Weight (Approx.) | 1800 kg | 2300 kg | 2600 kg | 2950 kg | 3400 kg | 3800 kg | ||
| Machine Dimension (Approx.) (LxWxH) | 1360 x 700 x 1450 | 1750 x 750 x 1800 | 1970 x 800 x 2000 | 2100 x 820 x 2060 | 2340 x 860 x 2110 | 2420 x 980 x 2150 | ||
*All dimensions are in mm
- Have any Query?
